HomeProductsSafety engineering with AS‑InterfaceSafety monitors with AS-InterfaceGMOX-PR-12DN-C16

GMOX-PR-12DN-C16 (Order no. 103267)

Choose content Description Choose content Technical data Components Accessories Choose content Ordering data

AS-Interface Safety at Work safety monitor with integrated Gateway GMOx

One AS-i master
Display and pushbuttons for diagnostics and adjustment
Memory card for different programs
Adjustable time-delay
16 OSSDs

Description

Gateway to Profibus

For connection to a Profibus DP as a slave and as a master for an AS-i bus according to specification 3.0. Detection of ground shunt, double addressing and EMC problems.

Rapid setup with the display without PC. Direct display of faults with plain-text messages. Comprehensive AS-i diagnostics integrated. AS-i configuration software is available.

OSSDs (Output Signal Switching Devices), AS-i outputs

Two OSSDs with two redundant normally closed contacts each

Two OSSDs with semiconductor outputs

12 additional safe AS-i outputs can be controlled

Inputs

4 inputs, freely selectable

Logic functions

Programmable with AsiMon software. All safety components can be programmed with different functions as inputs. The inputs can be linked with AND or OR gates or via logic functions such as FlipFlop, switch-on delay, OFF time or pulses.

Different programs can be stored on a memory card.

AS-Interface monitor

The monitor controls two AS-i circuits with up to 62 safe slaves and up to 16 outputs.

Display and pushbuttons

The display is used to operate the gateway functionality as well as the monitor at the same time. The diagnostics and maintenance functions are considerably expanded compared to the SFM monitors. They can also be launched on the display without a PC monitor.

Incorporated security functions allow the programmed functionality to be protected and monitored.

Power supply

Type N permits connection of several GMOx devices to the same power supply unit.

Important: A connection kit must be ordered for each safety monitor. See Accessories.

Dimensional drawings

Connection examples

Technical data

Approvals

Operating and display elements

Display	LCD AS-i slave address indication, error messages
LED display
	4 x LEDs EDM / start state of the inputs for the external device monitoring circuits: LED off: open, LED on: closed
	LED AUX auxiliary power is present
	LED U AS-i voltage OK
	LED prj mode, configuration mode active
	LED PROFIBUS master detected
	LED power, power supply ON
	LED AS-i active AS-i operation normal
	LED config error configuration error
	LED prg enable automatic slave programming possible
	4 x LEDs, output circuits, state of the output circuits: LED off: open, LED on: closed

Item	Extras	Color	Designation1	Number	LED	Slide-in label	Note slide-in label	Switching element	Version
				4					Pushbutton

Electrical connection values

Power consumption

9 W

Connection cross section

(2x AWG 24 to 12)

Flexible wire for cable end sleeve

(2x (0.5...1.5) mm²)

for wire

2x (0.5...1.5) mm²

Response delay

Safety circuit off

max. 40 ms

ASI operating current

max. 300 mA

ASI voltage

30 V

ASI cycle time

150 μs 150 x (number of slaves + 2)

Outputs

Number	Type	Function	Footnote
4	Output switching elements, output circuits 1, 2, 3 and 4	Relay outputs 1.13, 2.13, semiconductor outputs 1.14, 2.14, 3.14, 4.14

Rated insulation voltage U_i

500 V

Inputs

Number	Type	Function	Footnote
4	Feedback loop/start	EDM1/Start1: 1.Y1; EDM2/Start2: 2.Y1; EDM3/Start3:1.Y2; EDM4/ Start4: 2.Y2	(EDM: external device monitor / feedback loop)

Switch-on delay

10 s

Card slot

yes (Memory card to store the configuration data)

Mechanical values and environment

Number of OSSDs	16 (4 fed out)
Number of masters	1
Mounting type	Mounting rail 35mm according to DIN EN 60715TH35
Degree of protection	IP20
Ambient temperature	0 ... +55 °C
Material
Housing	Stainless steel
permissible shock and vibration load	According to EN 61 131-2

Characteristic values according to EN ISO 13849-1 and EN IEC 62061

Mission time	20 y
Category	4
Performance Level	PL e
PFH_D	5.36 x 10^-9
SIL CL	3

Miscellaneous

in compliance with	EN 61 000-6-2, EN 61 000-6-4, EN 62 061, IEC 61 508, EN ISO 13 849-1

in compliance with

EN 61 000-6-2, EN 61 000-6-4, EN 62 061, IEC 61 508, EN ISO 13 849-1

Interface

Bus data protocol	PROFIBUS according to EN 50 170-3
Data rate	9.6 ... 12000 kbit/s
Date interface	Serial interface RS 232
Periphery	Decentralized peripheral equipment mapping of the AS-i slaves as I/O process data in the PROFIBUS; complete diagnostics and configuration via PROFIBUS DP master

Downloads

Complete package

Download all important documents with a single click.

Content:

The operating instructions and any additions to the operating instructions or brief instructions
Any data sheets to supplement the operating instructions
The declaration of conformity

Download Complete Package (ZIP, 13,3 MB)