AnasayfaProductsSafety engineering with AS‑InterfaceMagnetically coded safety switches with AS-InterfaceCMS-R-AZA-01PL-AS1

CMS-R-AZA-01PL-AS1 (Sip. No. 105090)

Choose content Açıklama Boyut çizimleri Teknik Veriler Bileşenler Aksesuar İndirme bağlantısı Sipariş verileri

Non-contact safety switch CMS-R-AZA-01PL-AS1, with connecting cable and plug connector M12

Safety switches with integrated read head and integrated evaluation unit.
LED diagnostic displays
Operating distance 9 mm

Açıklama

Actuator

An appropriate actuator to suit the read head selected is required. The dimensions of the actuators are the same as those of the read heads, although the former have no connecting cable.

AS-Interface inputs

D0 - D3

Switch actuated/open

Evaluation is performed via a safety monitor.

AS-Interface output

D1	LED 1 on read head (only CMS-R-AZA...)

LED function display

The ASI LED (dual LED red/green) displays the colors red, green and yellow. The status of the switch and the bus is indicated via this LED.

LED 1 can be connected via the AS-Interface bus, e.g. to indicate the door state.

Principle of operation

Reed contacts are installed in the read head of the safety system CMS. The contacts blades on the reed contacts will close when under the influence of the magnetic field from the actuator. The read head only responds to the specific mating component, that is a specific actuator that is allocated to the read head type.

Dimensional drawings

Connection examples

View of connection side

Teknik Veriler

Approvals

Workspace

Operating distance on	min. 9 mm
Secured switch-off distance s_ar	max. 70 mm
Center offset
symmetrical, at distance s = 3 mm	2.5 mm

Electrical connection values

ASI operating current	max. 30 mA
ASI data in
according to AS-i Safety at Work	D0, D1, D2, D3 (Switch actuated = code sequence / switch not actuated = zero sequence)
ASI data out
LED red	D1 (1 = LED on)
ASI-LED
LED red/yellow alternately flashing	No data exchange between master and slave (Slave address=0)
LED red	No data exchange between master and slave (Master in the STOP mode / Slave not in LPS / Slave with incorrect IO;ID / Reset active on the slave)
LED green	Normal operation
LED red/green alternately flashing	Fault
LED red flashing	Fault
ASI slave type
according to ASI specification 3.0	EA code: 7
according to ASI specification 3.0	ID code: B
ASI voltage
DC	26.5 ... 30 ... 31.6 V

Mechanical values and environment

Connection type	hard-wired encapsulated cable with plug connector M12
Design	A
Installation orientation	any (During mounting it must be ensured that the marking arrows on the actuator and the read head are opposite each other.)
Cable length	1 m
Mechanical life	100 x 10⁶
Response time
after change in the actuation status	max. 5 ms
Degree of protection	IP67
Ambient temperature	-20 ... +60 °C
Material
Housing	Reinforced thermoplastic (PPS), fully encapsulated
Cable material	PUR
Method of operation	magnetic, reed contact

Characteristic values according to EN ISO 13849-1 and EN IEC 62061

Mission time	20 y
	Monitoring of the guard position
B_10D	3 x 10⁶
Category	3
Performance Level	PL e
PFH_D	4.29 x 10^-8

Miscellaneous

in compliance with	EN 60947-5-3: 2013; EN ISO 13849-1: 2008; EN ISO 14119: 2013; EN 62026-2: 2013 (AS-i)

in compliance with

EN 60947-5-3: 2013; EN ISO 13849-1: 2008; EN ISO 14119: 2013; EN 62026-2: 2013 (AS-i)

Aksesuar

Actuator

Actuator CMS design A

084592
CMS-M-AC

Cube-shaped version, 88 x 25 mm

Connection accessories

Bus coupling module with plug connector M12, 5-pin

105756
BCM-A-P2-SEM4-1

Conversion from M12 to ribbon cable
Very compact design
Easy handling

Mounting accessories

Spacer CMS-A-SA

110415
CMS-A-SA VPE10

Spacer for CMS read heads design A
Packaging unit 10 pieces

İndirme

Komple paket

Tüm önemli belgeleri tek bir tıklama ile indirin.

İçerik:

Kullanım talimatları ve kullanım talimatlarına veya kısa talimatlara yapılan tüm eklemeler
Kullanım talimatlarını tamamlayan tüm veri sayfaları
Uygunluk beyanı

Paketin tamamını indirin (ZIP, 1,2 MB)