SN02X12-732L-MC2507 (Rend. sz. 161182)

Válasszon tartalmat Ismertetés Méretrajzok Műszaki adatok Komponensek Tartozékok Letöltési link Rendelési adatok

Series SN... 12 mm, inductive

With 12 mm proximity switch spacing, the rated operating distance is 5 mm.

The switching elements are equipped as standard with a function display (yellow). The function display can be clearly seen from the exterior.

1)	Screwed in with metal adhesive. Plug connector(s) not aligned
2)	LED indicator
3)	Assured operating distance
4)	Actuator

Rated operating distances S_n	5 mm
Assured operating distances S_a	0.2 ... 4 mm (Dimension applies only to steel (ST37) and to EUCHNER trip dogs of series UX.. / GX..)
Switching hysteresis	0.2 ... 1.0 mm (in the installed state)
Repeat accuracy R	5 %
	Switching element, station 1
Center offset
at s = 1 mm read distance	m_OFF= (-) 4.2 mm and m_ON= (-) 4.0 (for side approach)
at s = 2 mm read distance	m_OFF= (-) 3.3 mm and m_ON= (-) 3.0 (for side approach)
at s = 4 mm read distance	m_OFF= (-) 0.5 mm and m_ON= 0.0 (for side approach)
at s = 3 mm read distance	m_OFF= (-) 2.5 mm and m_ON= (-) 2.0 (for side approach)
	Switching element, station 2
Center offset
at s = 4 mm read distance	m_ON= (-) 0.5 mm and m_OFF= 0.0 (for side approach)
at s = 3 mm read distance	m_ON= (-) 2.5 mm and m_OFF= (-) 2.0 (for side approach)
at s = 2 mm read distance	m_ON= (-) 3.3 mm and m_OFF= (-) 3.0 (for side approach)
at s = 1 mm read distance	m_ON= (-) 4.2 mm and m_OFF= (-) 4.0 (for side approach)

LED display
LED yellow	LED forward current I_Fmax.2.5 mA

Output type	PNP
Rated operating current I_e	250 mA
Operating voltage
DC	20 ... 24 ... 33 V Power supply unit with electrical isolation as per EN 61558-2-6 or sensor pulsing U_B(HIGH)
Operating current	max. 11 mA Current consumption without load
EMC protection requirements	EN 60947-5-2
Utilization category
DC-12	250mA, 33V (For DC-13, the output must be protected with a free-wheeling diode for inductive loads.)
Short circuit and overload protection, pulsed	Yes
LOW level
on sensor pulsing	0 ... 5 V DC
Off-state current Ir	max. 0.001 mA
Residual ripple
From U_Bor U_B(HIGH)	max. 10 %
Electrical switching frequency	max. 500 Hz
Safety class	I
Voltage drop U_d
DC	max. 2.5 V
Duty cycle T_on
T (HIGH) : T (LOW) on sensor pulsing	4 : 1
Test pulse duration
T (LOW) on sensor pulsing	0.1 ... 20 ms
Reverse polarity protection	Yes

Connection type	1 x plug connector, 7-pin (M17 receptacle 7-pin rapid-action coupling SPEEDTEC, vibration-resistant up to 25 G. INTERCONTEC order no. receptacle + insert: B EG A 863 NN 00 00 068A 000, contact pins: 61.004.11, wiring 0.14 mm² BK, 0.75 mm² GN/YE)
Number NC contacts	1 per switching element
Number of switching elements	2
Design	upright
Proximity switch spacing	12 mm
Storage temperature	-25 ... 70 °C
Degree of protection	IP67 (only screwed tight with the related mating connector.)
Ambient temperature	-25 ... 70 °C
Material
Housing	Die-cast aluminum
Active face	PBT

C number
C2507

Minden fontos dokumentum letöltése egyetlen kattintással.

Tartalom:

A használati utasítás és a használati utasítás vagy a rövid utasítás kiegészítései
A használati utasítást kiegészítő adatlapok
A megfelelőségi nyilatkozat