KezdőlapProductsTransponder-coded safety switches without guard lockingCTP-I-AP safety switch without guard lockingCTP-I-AP-U-HA-ZZ-SA-136732

CTP-I-AP-U-HA-ZZ-SA-136732 (Rend. sz. 136732)

Válasszon tartalmat Ismertetés Méretrajzok Műszaki adatok Komponensek Tartozékok Letöltési link Rendelési adatok

Transponder-coded safety switch CTP-I-AP, M12

Safety switch without guard locking, with integrated evaluation electronics
Short circuit monitoring
2 safety outputs (semiconductor outputs)
Up to category 4 / PL e according to EN ISO 13849-1
With plug connector M12
Unicode
Approach directions A, B and C (delivery state)

CTP-I-AP-U-HA-ZZ-SA-136732 (Rend. sz. 136732)

Ismertetés

Approach direction

Horizontal

Can be adjusted in 90° steps

Unicode evaluation

Each actuator is highly coded (unicode). The switch detects only taught-in actuators. Additional actuators can be taught-in. Only the last actuator taught-in is detected.

Pin	Designation	Function	Connecting cable conductor coloring
1	n.c.	-	-
2	UB	Operating voltage of AP electronics, 24 V DC	BN
3	FO1A	Safety output, channel 1	GN
4	FO1B	Safety output, channel 2	YE
5	OI	Diagnostic output	GY
6	OD	Door monitoring output	PK
7	0 V UB	AP electronics operating voltage, 0 V	BU
8	n.c.	-	-

Fuse
external (operating voltage UB)	0.25 ... 8 A
Power consumption	1 W
Rated insulation voltage U_i	50 V
Rated impulse withstand voltage U_imp	0.5 kV
Operating voltage DC
U_UB	24 V DC -15% ... +15% reverse polarity protected, regulated, residual ripple<5%, PELV
EMC protection requirements	Acc. to EN IEC 60947-5-3
Utilization category
DC-13	24 V 150 mA (Caution: outputs must be protected with a free-wheeling diode in case of inductive loads)
Switching load
according to UL	24V DC, Class 2 (alternatively, see operating instructions)
Safety class
EN IEC 61140	III
Current consumption
I_UB	40 mA
Test pulse duration	max. 0.3 ms (Applies to a load with C<= 30 nF and R<= 20 kohm)
Test pulse interval	min. 100 ms
Degree of contamination (external, according to EN 60947-1)	3
	Monitoring output OD, OI
Output type	p-switching, short circuit-proof
Output voltage	0.8xUB ... UB V DC
Switching current	1 ... 50 mA
	Safety outputs FO1A / FO1B
Output type	2 semiconductor outputs, p-switching, short circuit-proof
Output voltage
LOW U(FO1A) / U(FO1B)	0 ... 1 V DC
HIGH U(FO1A) / U(FO1B)	UB-1.5 ... UB V DC
Discrepancy time
both safety outputs	max. 10 ms Acc. to EN IEC 60947-5-3
Turn-on time	max. 400 ms
Off-state current I_r	max. 0.25 mA
Switching current
per safety output FO1A / FO1B	1 ... 150 mA

Approach speed	max. 20 m/min
Connection type	1 plug connectors M12, 8-pin
Extraction force	20 N
Ready delay	max. 1 s
Actuating force	10 N
Installation orientation	any
Switching frequency	max. 0.5 Hz
Mechanical life	1 x 10⁶
Overtravel	5 mm
Shock and vibration resistance	Acc. to EN IEC 60947-5-3
Degree of protection	IP67/IP69/IP69K (screwed tight plug connector/mating component)
Ambient temperature
at U_B = 24 V DC	-20 ... +55 °C
Material
Safety switch housing	Reinforced thermoplastic
Switch head cover	Die-cast zinc

Mission time	20 y
Category	4
Performance Level	PL e
PFH_D	4.1 x 10 ^-9

The following applies to the approval according to UL	Operation only with UL Class 2 power supply or equivalent measures; see operating instructions
Detent mechanism	Snap-in bolt

Rend. sz.	136732
Cikk neve	CTP-I-AP-U-HA-ZZ-SA-136732
Súly	0,364kg
Vámtarifaszám	85365019000
ECLASS	27-27-24-05 Safety-related transponder switch with guardlocking

Repeat accuracy R
according to EN 60947-5-2	10 %

CTP-I-AP-U-HA-ZZ-SA-136732 (Rend. sz. 136732)

Transponder-coded safety switch CTP-I-AP, M12

Ismertetés

Approach direction

Unicode evaluation

Connector assignment

Dimensional drawings

Connection examples

Műszaki adatok

Approvals

Workspace

Electrical connection values

Mechanical values and environment

Characteristic values according to EN ISO 13849-1 and EN IEC 62061

Miscellaneous

Tartozékok

Letöltések

Teljes csomag

Egyedi dokumentumok

Egyéb dokumentumok

CAD-adatok

Rendelési adatok